Відео

Make this is EXCELLENT EXPLANATION!!! Wgreat video

can i use this for lifting things on roofs just extend the rope

Man you are a hero. I have watched over 20 videos on how heat pump works, I was so confused, like fucking water actually mix with refrigerant? Like wtf, nobody mentioned or explained the coaxial coil and how it works. Thanks god I found your video

Thanks bro!

Just what I needed! I was wondering why no freon was going in.... Turns out I have no idea what I'm doing. But now I kinda do!

I stared my hvac business in Canada 12 years ago. I’ve always just wanted a balanced work life. I knew very little about business and hard to learn thru a lot of bumps. I was tired of working for somebody, counting on the weather to keep us busy. It’s so hard to get ahead in business, especially with the crazy economy. Here it’s hard to sell a 3 ton a/c system for 5000$. I see guys in the states that wouldn’t touch it for less than 10-15k. Business stresses me out. I’m tired of the rollercoaster and catch up game that always seems to be going on. Sometimes I wish I never got into this. There is a few perks for sure , but sometimes I just wish I stayed working for the man

Nice thank you I'm getting 15.7 across all three leg start run and common. It was a little hot but all three legs are Reading the same so it is not grounded or in thermal lockout. But when the 24 volts are engaged the compressor stays at 290 on the low side and high side it is not adjusting in any way.

Any review on the pocket version I think it’s the pocket 2

Usually one of the worst issues these units have that is always not addressed at the factory is bad soft foot from those formed bases. I routinely see 0.020-0.050” soft foot.

Found one like that on a carrier today tripping the breaker

can you cut steel with that rig? Also, when brazing, do you have the option of using just MAPP or do you have to use O2 all the time?

Geat video. I know you did not flow nitro for demonstration purposes, what is the best way to remove those flakes from that txv afterwards?

Boring mtfkr

How much was the set, an estimate since it was last year. And how much is each tank? 🤔✌🏾 I’ll plan ahead, thanks in advance.

the whole static pressure is a shit fools gimic to make more money

Golf clubs? Lame.

Is it Boost spp6 would be efficient for 45+5 mdf capacitor? Thanks!

.

Hey is it possible to use the super evac manifold on a Mitsubishi heat pump for example the MXZ models when pulling vacuum, on the port inside the heat pump? Basically I was wondering if it’s possible to connect 2 hoses there to pull a vacuum faster. @hvacknowitall

You have comprehensively covered the whole topic in such a short description n video. It's an incredible brief technical guide

Always ask if the nitrogen cylinder has been used for clean nitrogen only. Sometimes the cylinder was used for some other gas and it just gets repainted. If it has had some other gas in it you now have dirty nitrogen and you can get high levels of copper oxide inside even though it's clean gas. If possible get only medical grade nitrogen, the sales person will probably give you a strange look but tell them that is what you want. And even with clean and pure nitrogen you will get some copper oxide build up.

Cheking superheat near desire temperature

Very good

Heat the joint first. If your gap is snug, heat will transfer quickly to pipe. If not snug, use a lever type swaging tool.

The 40 F minus 75 F in my opinion . The 40 F . is just the temperature at what the refrigerant begins to boil with out gaining any heat just as soon passed through the metering device. The more standard temperature measurements is Delta T . Temperature of the air coming in the evaporator and temperature coming out of the evaporator. The other temperature that is importance is S.H that is the gain of heat in the refrigerant after it saturated or is changing state from liquid to vapor. But this is a different way to see the temperature difference Thanks

My Heil furnace is eating blower wheels. It's getting it's second wheel this week. They're only lasting maybe 4 years.

Excellent 😊

What's an acceptable pressure check drop in PSI over 10 or 20 min. 1 or 2 psi. Is there a few psi range that temperature of the gas can fluctuate. Depending on the bottle temp vs system temp. I'm praying you tell me the good news. I let the gas into the system. It held 250 micron vac for 15 min no problem. I had to fiddle with the setup a bit. Most of these inverter systems have 3/8 ports and i didn't have 3/8 to 3/8 hoses or enough adapters. And cheap core removal tools. One of them leaked. one didn't. And some don't grab the core. Check that too

Surf bro channel highlighted the white textured insulation falls apart and corrodes line sets. I confirm that with a neighbors unit, a few years old. It looks like someone hit it with a torch and it's just gone in many spots. UV eats is. And it corroding the set quite bad. Those guys love the k-flex. I'd consider buying that stuff for sure. I premade set has jumbo neoprene style and it tears, but not as bad as i thought. But it definitely doesn't glide at all. And will help get it stuck in a whole and bunch up.

3/4 by hand kinks fast, especially if you go fast and go against the previous coiled up direction. Get a good bender. My cheap one on 90's looks funny, but still acceptable. Maybe it's the copper producer influencing the bend shape/tension. The bender is pretty nice in function, it's like all the other ratchet ones.

Thanks man!

Do these give you a superheat and subcool reading like the field piece does

You missed Highside Chemicals "Just For Copper" its basically a copper glue. and has its place like each method you discussed, Just like Staybright 8 solder over brazing

What are your thoughts on silver bearing solder/soldering? Just heard about it and am unsure

Found one leaking through regardless off the adjustment position. Any tips before condemning?

I use telta D

Are they refillable?

Would this just be called superheat? Genuinely asking.

To the point and informative, no fluff. Right on brother.

What is the main reason for the acces port?

Do you recommend always change your txv when changing a compresor.?

Can you make a video about Stay Brite 8 as an alternative to high temp brazing?

🫤several residentials with o2? Not the way I shake and roll. 😆 And cramp! 🥴 But still really like the idea. I have bunch of 30 year old Goodman heat pumps for 3 rd floor Apts and no elevator. So, my old ass would benefit greatly with this. Appreciate maaaan. 🫵👍 I haven’t heard you going back because of a crappy joint, must be doing something right.

Always appreciate, concise. 🫵👍

Cool Video. Brazing with Nitrogen is cool.. i put regulator on 3.. at 6 I notice nitrogen pushing out filler... had that ever happened to you

And you divide 35:in half and you get 17.5, which is close to your 20 degree split, which makes sense because that's halfway between the return air and the evaporator coils it passes through.

Heat the pipe then the joint

Nitrogen brazing is a thing

Great video tech

The difference is important!